Standard deviation
In probability and statistics, the standard deviation is the most commonly used measure of statistical dispersion. Standard deviation is defined as the square root of the variance. It is defined this way in order to give us a measure of dispersion that is 1) a non-negative number; and 2) has the same units as the data.
We distinguish between the standard deviation σ (sigma) of a whole population or of a random variable, and the standard deviation s of a sample. The formulas are given below.
The term standard deviation was introduced to statistics by Karl Pearson (On the dissection of asymmetrical frequency curves, 1894).
Interpretation and application
Simply put, the standard deviation tells us how far a typical member of a sample or population is from the mean value of that sample or population. A large standard deviation suggests that a typical member is far away from the mean. A small standard deviation suggests that members are clustered closely around the mean.
For example, the sets {0,5,9,14} and {5,6,8,9} each have a mean of 7, but the second set has a much smaller standard deviation.
Standard deviation is often thought of as a measure of uncertainty. In physical science for example, when making repeated measurements the standard deviation of the set of measurements is the precision of those measurements. When deciding whether measurements agree with a prediction, the standard deviation of those measurements is of crucial importance: if the mean of the measurements is too far away from the prediction (with the distance measured in standard deviations), then we consider the measurements as contradicting the prediction. This makes sense since they fall outside the range of values that could reasonably be expected to occur if the prediction were correct.
Definition and shortcut calculation of standard deviation
Suppose we are given a population x1,...,xN of values (which are real numbers). The mean of this population is defined as
(see summation notation) and the standard deviation of this population is defined as
A slightly faster way to compute the same number is given by the formula
The standard deviation of a random variable X is defined as
Note that not all random variables have a standard deviation, since these expected values need not exist.
If the random variable X takes on the values x1,...,xN with equal probability, then its standard deviation can be computed with the formula given earlier.
The unbiased estimator for the standard deviation of a population, given only a sample of values x1,...,xn, is calculated by
This is also known as the sample standard deviation.
Rules for normally distributed data
In practice, one often assumes that data is approximately normally distributed. If that assumption can be justified, then 68% of the values are at most 1 standard deviation away from the mean, 95% of the values are at most two standard deviations away from the mean, and 99.7% of the values lie within 3 standard deviations of the mean. This is known as the "68-95-99.7 rule".
Relation between standard deviation and mean
The mean and the standard deviation of a data set go hand in hand and are usually reported together. In a certain sense, the standard deviation is the "natural" measure of statistical dispersion if the center of the data is measured by the mean. The precise statement is the following: suppose x1,...,xN are real numbers and define the function
Using calculus, it is not difficult to show that σ(r) has a unique minimum for
Geometric Interpretation
To gain some geometric insights, we will start with a population of three values, x1,x2,x3. This defines a point P= (x1,x2,x3) in R3. Consider the line L = {(r,r,r) : r in R}. It's the "main diagonal" going through the origin. If our three given values were all equal, then the standard deviation would be zero and P would lie on L. So it is not unreasonable to assume that the standard deviation is related to the distance of P to L. And that is indeed the case. Moving orthogonally from P to the line L, one hits the point
whose coordinates are the mean of the values we started out with. A little algebra shows that the distance between P and R (which is the same as the distance between P and the line L) is given by σ√3. An analogous formula (with 3 replaced by N) is also valid for a population of N values; we then have to work in RN.
Related articles
Referenced By
Acronym/Medical List | Letters used in Maths and Science | List of letters used in mathematics and science | List of mathematical topics (S-U) | List of medical abbreviations | List of medical acronyms | List of probability topics | List of statistical topics | ProbabilityApplications | Probability Applications
|
